Additional Information

 

 

Were you in search of guidance on How to Install a Bathtub?

Mounting a tub isn't exactly brain surgery, however it does require strong plumbing, carpentry, and also often, tiling skills. Changing an old tub with a new one is likewise a moderately tough project. If the old bathtub is readily obtainable, the job can relocate immediately; if you have to open up a wall to get rid of the old tub and also position the brand-new tub, the task is much harder. In either instance, the job is within a residence handyman's skills, although you will certainly require a helper to vacate the old bathtub as well as embeded in the new one. Make sure you have actually qualified on your own for the job as well as fit attempting it. As opposed to employing a contractor to take over a halfway-completed task, it is better to take into consideration employing one prior to you begin. Possibilities are you might need a specialist plumber to make tube connections.
This post will certainly assist you mount a new tub in your washroom if you have currently bought a new bathtub and don't require to change the plan of your previous water pipes.
Your devices and also material checklist need to comprise the following:

 

• New Tub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Chisel


• Tape Measure


• Pipeline Caps


 

Preparing for the Setup

To start with, the sustaining frame supplied with the bathroom needs to be fitted (if required) according to the producer's guidelines. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is necessary to make sure that if the tap includes a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the faucets device to prevent stress on the tub.
Fit the adaptable tap connectors to the bottom of the two taps making use of 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet with the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Make sure you use all of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom ought to now prepare to be suited its last placement.

 

 

Removing Old Touches

If you require to replace old taps with new ones as a part of your installation, after that the first thing you must do is detach the water system. After doing so, turn on the taps to drain pipes any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be quite problematic as a result of the restricted access that is often the instance.
Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the faucets. Have a fabric ready for the continuing to be water that will certainly originate from the pipes. Once the supply pipelines have actually been removed, use the very same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary taps from turning throughout this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any type of old sealing substance.
Before carrying on to fit the new faucets, compare the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.

 

 

Installing the Bath tub

Using both wood boards under its feet, put the bathtub in the needed position. The wooden boards are handy in evenly spreading out the weight of the bathtub over the location of the boards instead of focusing all the weight onto 4 small factors.
The next goal is to make certain that the tub is leveled all round. This can be attained by checking the level and also adjusting the feet on the bath tub until the spirit level reviews level.
To set up faucets, fit the bottom of the outermost adaptable tap port to the ideal supply pipe by making a compression join; then do the exact same for the various other faucet.
Switch on the water system and also check all joints and new pipework for leakages and tighten them if required. Fill up the bath tub and likewise examine the overflow electrical outlet and the typical electrical outlet for leakages.
Finally, repair the bathroom paneling as defined in the supplier's instruction manual. Tiling and sealing around the tub must wait till the bath tub has been utilized a minimum of when as this will certainly settle it into its final setting.

 

 

Suitable New Touches

If the tails of the brand-new faucets are plastic, then you will need a plastic port to avoid damages to the string. One end of the adapter fits on the plastic tail of the faucet and the other end offers a connection to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly call for lowering couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, place the faucet in the installing opening in the bath/basin making sure that the washing machines remain in area in between the faucet and also the sink. Safeguard the faucet in position with the supplier given backnut. As soon as the faucet is firmly in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet ports. The previous kind must be linked to the faucet ends first, tightening only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been attached.

 

 

Tiling Around the Bath tub

In the location where the bath satisfies the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can move enough to fracture an inflexible seal, creating the water to permeate the wall between the bathroom and also the tiling, causing issues with moisture and feasible leakages to the ceiling listed below.
You can choose from a variety of coloured sealers to assimilate your fixtures and installations. They are offered in tubes as well as cartridges, and can securing gaps up to a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of drenched paper or soft rope. Remember to constantly load the tub with water before securing, to permit the motion experienced when the tub remains in usage. The sealant can fracture relatively early if you do not take into consideration this movement prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally easily readily available on the marketplace. It is advisable to fit the floor tiles utilizing waterproof or water resistant adhesive and also grout.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

 

I was introduced to that editorial on A Step-by-Step Guide to Installing a Bathtub from an associate on a different domain. Do you know anybody else who is fascinated with the niche? Please feel free to promote it. Thank you so much for taking the time to read it.

Set Up An Appointment